How to Increase Water Pressure in Your Shower

Do you have an issue with low water pressure in your shower? Indianapolis homeowners can take a few simple steps to increase the flow, whether it’s a longtime issue or a recent problem.

Let’s look at why your water pressure might be low and some methods to improve it.

Why Is My Water Pressure Low? Finding the Cause

The first step is figuring out what’s causing your pressure problems. Several issues, including a clogged showerhead, low pressure from the water utility, or water flow restricted by flow regulators, can cause low water pressure.

You'll need to do some detective work to determine the cause of your low water pressure:

  1. Check the Showerhead

Is there gunk or limescale caking your old, formerly reliable showerhead? If you determine that the issue is a clogged showerhead, here’s the easiest way to clean it:

  • Fill a plastic bag with white vinegar and attach the bag to the showerhead with a twist tie or rubber band.

  • Leave the bag attached for a couple of hours before removing it.

  • Run the hot water for a few minutes to clear the vinegar.

 

You should notice an immediate increase in water pressure. If it’s not a clog, it might be time for a replacement. Certain showerheads have a regulator in them that restricts water flow and affects the pressure. Our professionals can repair or replace your showerhead and recommend the best options for your home.

Consider upgrading to a showerhead specifically designed to increase water pressure. High-pressure showerheads are usually equipped with a pressure-boosting feature that allows you to adjust the flow and impact of the water. However, showerheads that increase water pressure come with a cost. Retailers usually offer high-pressure showerheads that use up to 1.8-2.5 gallons of water per minute, meaning your water bill will likely go up.

Some showerheads can be fitted with water-saving features that help to conserve water while maintaining the desired pressure.

  1. Check the Water Line Valve and Water Pressure Regulator

Restricted water flow could also be to blame, especially if you notice low water pressure in the shower after replacing a water line valve. Double-check the valve to make sure it’s installed correctly and is in the “open” position. If the water pressure is still weak, you might have a faulty valve.

You can also try increasing the water pressure by gently adjusting your water pressure regulator. This water safety feature is usually located near the main water supply and allows you to adjust the pressure levels. It can go bad, allowing your water pressure to shift above or below the safe 46-60 psi range, and it should only be replaced by a qualified plumber. You may have a faulty water pressure regulator if you notice leaking around your water heater or toilet, water comes out of your faucets in a sudden burst when turned on, or your water pressure suddenly drops throughout your house.

  1. Check Water Pressure Throughout Your Home

If there’s low water pressure in an upstairs shower or bathroom, it’s essential to check the water pressure in other areas of the home. If the pressure is low throughout the house, the issue may be caused by a problem with the main water line, though without the leaking of a faulty water pressure regulator. It’s best to contact a qualified plumber to identify the cause and address, whether the issue is in the water main or the regulator.

The issue may be a low-pressure valve in the upstairs bathroom if the pressure is normal in other areas. If this is the case, replacing the valve with a higher-pressure one may be necessary, or installing a showerhead designed to increase water pressure and flow, as mentioned above.

During colder weather, frozen pipes may be to blame if the bathroom is located against an outside wall. The pros at One Hour Heating & Air Conditioning of Indianapolis can help ensure that every part of your home stays warm, comfortable, and free of frozen pipes.

  1. Check Your Hot Water Heater

Is your problem only with low hot water pressure, even though your cold water runs normally? Your hot water heater is the likely culprit, especially if you notice yourself running out of hot water fast or replenishing it more slowly. If you think your water heater is the culprit, start by calling in a professional plumber for a maintenance check. A professional inspection will catch any possible issues or rule out your water heater as the cause of low water pressure. As a bonus, that leaves your annual maintenance done for the year!

  1. Talk to Your Utility Company

Sometimes, nothing in your home is causing the problem. If the issue is with low pressure from the water utility, you can contact them to inquire about ways to increase the water pressure in your home. They may be able to suggest solutions or increase the pressure level.

Get Your Hot Water Pressure Back to Normal, Fast

Benjamin Franklin Plumbing of Indianapolis is perfect for timely assistance with any plumbing troubles, from low water pressure to more complex issues. You’ll receive top-notch service from skilled plumbers with experience handling a variety of plumbing services. Call today at (317) 316-3261 or book an appointment online.